Installation/Owner’s ManualModel 9050Model 9050Model 9050Copyright 2009 DoorKing, Inc. All rights reserved.TMCopyright 2011 DoorKing, Inc. All rights
9050-065-M-3-118Slide Gate Requirements The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with
9050-065-M-3-119Slide Gate Protection ReverseLoopAutomaticExit LoopMinimizes the potential of the gate closing when a vehicle is present. Number and p
9050-065-M-3-1110Gate End RetainerEnd Post SECTION 1 - INSTALLATION 1.2 Physical Stops for the Gate 1.1 Hardware for the Gate Good hardware is essent
9050-065-M-3-11111.3 Typical Gate TypesThe Model 9050 operator is designed to be installed on these gate types. See the next 4 pages for specific oper
9050-065-M-3-11121.4 Operator Mounting Positions• Operator’s chain idler wheels are factory set for the front position. • Remove only the top cha
9050-065-M-3-1113• Set one chain Idler wheel at the top and one in the center position on one side of the operator. • Remove both chain knockout
9050-065-M-3-1114Note: Chain stops CANNOT be used for this installation. End post with a gate end retainer must be installed as the physical stop if
9050-065-M-3-11151.5 Underground Conduit RequirementsSweepsConcretePadPrimary Operator Position Secondary Operator Position • Operator’s setup is the
9050-065-M-3-11164” 11” Solenoid Lock Conduit Area 2.5” Electronic Box 1.6 Pad, Post or Ceiling Mount without/with J-Box SetupPost Mount with Condui
9050-065-M-3-11171.7 Mounting Operator and Chain1” minimum from operator housing to gate. Prior to mounting the operator, be sure that the correct cha
9050-065-M-3-1118Endless Idler Assembly (On Select Installations) 1.8 Installation of Warning SignsThis DoorKing Slide Gate Operator is shipped with
9050-065-M-3-11192.1 High Voltage Wire Runs2.2 High Voltage Terminal ConnectionIf power wiring is greater than the maximum distance shown, it is recom
9050-065-M-3-1120L1NCNOSELFTESTTIMEDELAYREVSENSREVERSE LOOPEXIT LOOP1ON2 3 4 5 6 7 81211109876543219410L194103.1 4702 Circuit Board Description and A
9050-065-M-3-11217-OFF7-OFF7-ON7-ON8-OFF8-ON8-OFF8-ONGate CloseBack-OffPositionGate OpenBack-OffPositionNormal Setting. Gate fully opens. Gate stops s
9050-065-M-3-11223.3 Automatic Open / Close Limit AdjustmentGate MUST open until it contacts the physical “open” stop. (if gate starts to close, turn
9050-065-M-3-1123Give open command to cycle the gate or momentarily jumper terminals 8 and 12 to open gate.While gate is cycling, slowly rotate revers
9050-065-M-3-1124NCNOSELFTESTTIMEDELAYREVSENSREVERSE LOOPEXIT LOOP1ON2 3 4 5 6 7 81211109876543214702-010WARNINGMOVING GATE CAN CAUSEOperate gate onl
9050-065-M-3-1125NCNO4702-010121110987654321Gate FrameGate Frame5”or Lessor LessNon-Secure Side Outside PropertySecure Side Inside PropertyFiller Post
9050-065-M-3-1126NCNO4702-010121110987654321NCNO4702-010121110987654321Wireless Reverse Edge Sample Setup - Single ReceiverPhoto Sensor and Wireless
9050-065-M-3-1127Reverse4 Ft. min. to avoid gatemovement interference.4 Ft. min. to avoid gatemovement interference.4 Ft. min. to avoid reverseloop in
9050-065-M-3-111DoorKing, Inc. reserves the right to make changes in the products described in this manual without notice and without obligation of Do
9050-065-M-3-1128DANGERHIGH VOLTAGE!5.1 Main Terminal DescriptionLow Voltage CommonDry Relay ContactEarth GroundCircuit Board PowerCircuit Board Powe
9050-065-M-3-1129NCNO4702-0101211109876543215.2 Control Wiring for Single/Primary OperatorKey SwitchStand-AloneKeypadStand-AloneCard ReaderTelephoneEn
9050-065-M-3-1130NC NO 4702-010 12 11 1 2 3 45 6 10 9876 5 4 3 2 1 NC NNO UL 325 Terminal Open Photo Close Photo Open Edge NC NO 4702-010 12 11 1 2 3
9050-065-M-3-1131SECTION 6 - OPERATING INSTRUCTIONSWARNING - To reduce the risk of injury or death: 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. N
9050-065-M-3-11326.2 Shutdown ConditionsUnder various entrapment conditions the operator will assume either a soft or hard (alarm) shutdown. To deter
9050-065-M-3-11336.3 Manual Gate OperationFail-Safe Manual Release System (Factory Installed)This operator is equipped with one of two types of manual
9050-065-M-3-1134Key Release Emergency Vehicle Access Conditions Fail-Secure Manual Release System (Owner Installed)This manual release system (Insta
9050-065-M-3-11357.1 MaintenanceSECTION 7 - MAINTENANCE AND TROUBLESHOOTINGInspection and service of this gate operator by a qualified technician shou
9050-065-M-3-11367.2 TroubleshootingHave a good VOM meter to check voltages and continuity. A Meg-Ohm meter capable of checking up to 500 meg-ohms of
9050-065-M-3-1137Symptom Possible Solution(s)• Check the input LEDs. Any ON will hold the gate open and indicates a problem with a keying device. •
9050-065-M-3-112SPECIFICATIONS 1SECTION 1 - INSTALLATION 10SECTION 2 - AC POWER TO OPERATOR(S) 19ASTM 2200 Standard for Gate ConstructionImportant Sa
9050-065-M-3-11387.3 Accessory ItemsThe following accessory items are available for the model 9050 slide gate operator.Contact Sensors - For use as a
9050-065-M-3-1139Model 9050 1/2 HP 115 VACReset AC Power Alarm Blue Blue Blue Red Red Red White White BrownBrownBrown Brown Black Black White White Wh
Installation/Owner’s ManualModel 9050Model 9050Model 9050Copyright 2009 DoorKing, Inc. All rights reserved.Use this manual for circuit board 4702-010
9050-065-M-3-113SECTION 4 - ENTRAPMENT AND SAFETY PROTECTION 244.1 UL325 terminal Description4.2 Secondary Entrapment Protection Device Locations4.3
9050-065-M-3-114Instructions regarding intended installation: Vehicular gates should be constructed and installed in accordance with ASTM F2200; Stan
9050-065-M-3-115• For gate operators utilizing contact sensors: 1. One or more contact sensors shall be located where the risk of entrapment or obs
9050-065-M-3-116UL 325 Entrapment ProtectionClass I Class I and IIClass IIIClass IVClass II Class III Class IV A vehicular gate operator (or system)
9050-065-M-3-117Glossary GATE - A moving barrier such as a swinging, sliding, raising, lowering, or the like, barrier, that is a stand-alone passage b
Comments to this Manuals