Controlled-products-systems-group PATRSL User Manual

USAutomatic PATRIOT RSL High Quality Low Voltage Vehicular Slide Gate Operator Solar or AC Charged PATRIOT RSL Slide Gate Operator I

8Mounting Operator PAD MOUNT: The operator base has four predrilled holes and four access holes, which are covered with press in hole plugs. These

9STEP 1 Pad Mount Installation CONCRETE PAD CONSTRUCTION The mounting foundation must be very stable and of sufficient strength to prevent an

10STEP 2 Mounting of Chain Brackets to Gate With the operator securely mounted use the following procedure to locate and install gate brac

11STEP 4 Installation of Charging Source SOLAR PANEL Locate and mount the solar panel bracket so that the panel faces south

12Step 6 Current Sense Adjustment The control board has two current sense adjustments, MASTER and SLAVE (see illustration 17). Dual gates will requ

13LIMIT SWITCHES The limit switch adjustments are located on the top shelf of the operator. Remove the cover from the operator to make

14STEP 9 Making Final Adjustments Once gate is operating correctly using the “Open / Close Command” pushbutton it is time to setup the radio contro

15Circuit Board & Terminal Description Patriot Control Board TERMINAL DESCRIPTION 1 + 12 volt DC Output. *Maximum curr

16DS1 Programming Switches Factory settings are shown in bold italic type 1 Automatic close timer enable ON Timer to clo

17DS2 Programming Switches Factory settings are shown in bold italic type 1 Solenoid lock enable / Gate in operation indicator ON So

18SAFETY SECTION USAutomatic gate operators are certified to UL-325 Vehicular Class I and Class II slide gate standards. UL325 identifies

19SAFETY SECTION INSTALLATION a) Install the gate operator only when: 1) The operator is appropriate for the construction of the gate and the u

20SAFETY SECTION All safety features required by UL-325 and more are incorporated in the capabilities of all USAutomatic Control boards and should

21SAFETY SECTION Remedies for Safety Concerns Zone 1 Safety edges and photo electric eyes are the most common types of pro

22SAFETY SECTION Remedies for Safety Concerns Zone 4 This area is best protected with a photo eye or contact edge wired to the seco

23MONTHLY SERVICE All gate operators require periodic checking and adjustments by a qualified technician of the control mechanism for force (load),

24TROUBLESHOOTING SECTION OUTLINE 1 My slide gate operator will not operate. 2 Emergency release knob cannot be pulled. 3 I can hear gate operat

25Limit Cam Nut - Two limit cam nuts are located on the top of the operator; the limit nut locking plate is spring-loaded and must be depressed befo

26charging power of the solar panel. Verify that solar panel leads are connected to the battery correctly; panel is facing a southwest direction and

27 7. Gate opening or closing stops and reverses direction and then stops and will not operate STEP 1 This is most likely caused by an incorrect

1INTRODUCTION This operator is intended to be installed on vehicular Class I or Class II gates as defined by UL-325. Maximum gate load not to excee

2811. Transmitter will not operate the gate STEP 1 Verify the battery in the transmitter is good. Also verify that the dipswitches inside the tran

29STEP 5 Go to page 33 “Resetting receiver P2 relay to momentary mode” STEP 6 If this does not correct the problem return to troubleshooting secti

30Accessory Wiring Information USAutomatic Patriot gate operators are 12 vdc powered, solar charged operators do not require 110-vac for proper oper

31Accessory Wiring Before wiring accessories to the Patriot control board remove the actuator connector plug from the control board, this will disco

32Security Shunt – Used to control a Photo-Eye If installing a photo-eye on a solar gate operator the standby current draw of the photo-eye will dra

33Step 11 Programming Transmitter and Receiver (model 433DSR2LC) The Transmitter and Receiver provided operate at 433 MHz. Receiver can store up to

34STEP 12 Programming wireless Keypad (model 433 KPD) Terms to understand: Master Password – The 5-digit code used to access programming features.

35Changing Security Code This keypad has a virtual dipswitch used to create your Security Code. The virtual dipswitch contains nine 3-position switc

36Deleting Single Access Code: 1 Enter the Master Password. 2 Press the “7” key. If correct, 2 short beeps (if 1 long beep is heard, start over wi

37 Loops Safety and Exit Loop Position Diagram Proper wiring of two loops performing the same func

2Table Of Contents Page Introduction...1 Table of Contents...

38Loops Loop Size Chart The loop size is based on the width of the driveway. If the driveway is 14' wide, the loop would be a 6'x6'

39 NOTES PAGE _____________________________________________________________________________________________________________________________________

40NOTES PAGE ______________________________________________________________________________________________________________________________________

USAutomatic PATRIOT RSL Slide Gate Operator Limited 5 Year Warranty The PATRIOT RSL Slide Gate Operator is warranted to be free of defects in mat

3GENERAL REQUIREMENTS General hand/tools such as wrenches [7/16, 3/4], tape measure, level, clamps, chain cutter, etc. are required. Your particula

4IMPORTANCE OF A PROPERLY DESIGNED GATE As a general rule, a gate, which is to be automatically operated, must be stronger and smoother than one,

5PARTS INCLUDED The Patriot RSL slide gate operator is shipped in two separate boxes. One box contains the operator chassis, emergency release acce

6Operator Illustration and Descriptions Note: USAutomatic is not responsible for failure to comply with UL-325

7Mounting Operator NOTE: Do not mount in areas by automatic sprinklers, or flood-prone areas. It is important that the control board, control devic