Controlled-products-systems-group 3500ETL-1K User Manual

1 Rev 1.0 INSTALLATION MANUAL 3500ETL-1K 3600ETL-1K (Dual) Light Commercial Swing Gate Operator

10 2 - 3500ETL-1K/3600ETL-1K Operator Installation (Continued) STEP 5: Install the drive unit on the mounting bracket using (4) 1/2” x 3/4” hex bolt

11 2 - 3500ETL-1K/3600ETL-1K Operator Installation (Continued) STEP 9. Push the arms assembly up against the gate in the closed position. Make sure

12 2 - 3500ETL-1K/3600ETL-1K Operator Installation (Continued) 2.5 - Left Hand and Right Hand Operation Wiring For a single gate installation, conn

13 2 - 3500ETL-1K/3600ETL-1K OPERATOR INSTALLATION (Continued) Figure 16: Limit Assembly 2.6 - Learning and Limit switch adjustment Apollo has taken

14 2 - 3500ETL-1K/3600ETL-1K OPERATOR INSTALLATION (Continued) 5. Adjust the Collar Open (See Figure 16) until the GREEN light illuminates on the f

15 2 - 3500ETL-1K/3600ETL-1K OPERATOR INSTALLATION (Continued) 2.6 - Learning and Limit switch adjustment (Continued) 8. Press “OK” to allow the co

16 3 - CIRCUIT BOARD LAYOUT Figure 21 - CONTROL BOARD BUTTONS Figure 22 - CIRCUIT BOARD LAYOUT

17 Auxiliary Inputs 1 (16) and 2 (18): These digital inputs may be connected to the digital outputs of accessories and pro-grammed to activate or con

18 MOTB: Moon Touch programmable keypad with secure codes (up to 9 digits per code if required) to control gate opening and closing. Connects to the

19 SMXI/A Plugin Receiver: The SMXI/A 433Plug-In Receiver provides up to 15 channels for specific control of individual gate functions. The receiver

2 Table of contents IMPORTANT SAFETY INSTRUCTIONS …………………………………………………………...II APPLICATION ….……………………………………………………………………………………… III PRE-INSTALLATIO

20 OVIEW (see page 6 for Picture of OVIEW) Programming and diagnostic unit which connects directly to the gate controller and is part of the Nice “O

21 6.3 - Guard station 34 OPEN (NO) 35 STOP (NC) 36 CLOSE (NO) 37 GND With the Guard Station switches installed, the user can operate the gate by pu

22 Proper inspection of all equipment is required to ensure continuous functionality, safety and to ensure reliable op-eration in all weather conditi

23 8 - GENERAL LAYOUT AND SAFETY ACCESS Figure 32 - Photocells Installation Diagram Figure 31 - Loop Sensor and Photocells Installation Diagram

24 EXTERNAL ENTRAPMENT PROTECTION: Non-contact and contact sensors must be installed individually or in combination with each other to provide ext

25 Figure 33 - GENERAL BOARD OVERVIEW THE PROGRAMMING BUTTONS INDICATED IN THE ABOVE REFERENCE SHOULD BE USED ONLY AFTER UNDERSTANDING THE MANUAL AND

26 11 - PROGRAMMING BUTTONS Static: Set sensitivity to constant force on a scale of 1 to 10 (1 being the most sensitive). Dynamic: Set sensitivity o

27 11.5 - Function Learn: Puts the gate operator into learning mode for a Swing or Slide gate and Blue BUS peripherals. Learning mode for a Swing or

28 11.5 - Function (continued) Radio Channel: For the Plug-in Onboard Receiver, 15 radio channels may be programmed with one of the following option

29 11.5 - Function (Continued) Events (continued) To program weekly events EV1 through EV8, perform the following steps: 1. Press FUNCTION ->

3 WARNING - To reduce the risk of injury or death: xxREAD AND FOLLOW ALL INSTRUCTIONS. xInstallation should be performed by a professional install

30 11.5 - Function (Continued) Advance Settings: The following settings are available for customizing the gate operator as required by the custom-er

31 11.6 - Display ESC: Exit the DISPLAY menu. Info: Displays the manufacturer name, product name/model, software versions, and serial number. Clock

32 CLASS IV - RESTRICTED ACCESS VEHICULAR GATE OPERATOR - A vehicular gate operator (or system) intended for use in a guarded industrial location or

33 TABLE 3 SYMPTOM(S) POSSIBLE SOLUTION Operator will not pow-er On. Power LED is OFF x Check terminal Lock wiring for loose or broken wires x Chec

34 Steps on how to place the Apollo 1050 control board into learning mode. 1. Press Function 2. Press OK 3. Select Swing 4. Select weight of gate (

35 Left box is for installer check off and the right box is for customer check off. 1. The gate has been checked to make sure it is level and moves

36 LIMITED TWO-YEAR WARRANTY Apollo Gate Operators are warranted against defects for a period of 24 months from the date of purchase, providing

4 APPLICATIONS The Model 3500/3600 Swing Gate Operator is designed for residential and commercial applications. The 3500/3600 is listed with ETL and

5 PRE-INSTALLATION CHECKLIST The following check list should be used before beginning installation: Verify that the proper operator has been selec

6 PART IDENTIFICATION OPTIONS Part# 273 - CAUTION Sign (2 each) Part# 201 5 Watt Solar Panel & Bracket Part# OVIEW Part# 320N Nice Transmit

7 POST LOCATION GUIDE 1 - 3500ETL-1K/3600ETL-1K POST INSTALLATION DIMENSIONS Determine the angle that the gate will open to (A). Select the post c

8 2 - 3500ETL-1K/3600ETL-1K Operator Installation Horizontal center line of where gate bracket is to be installed STEP 1: The 3500/3600 operator

9 2 - 3500ETL-1K/3600ETL-1K Operator Installation (Continued) STEP 2. Mount the control box as close to the operator as possible (recommended within