Controlled-products-systems-group 4300SW User Manual

Revision 1.0.1_08-2012Nice Apollo Swing Gate OpenerVehicular Swing Gate Opener4300 SW - 1/2 HP 4500 SW - 1 HP

8screw and move the arm for the close limit until the RED light illuminates on the front of the control board (see Figure 13 steps 4-5-6-7). When the

9%HFTQD"(1"4(3!. 1#+ 8.437 - CIRCUIT BOARD LAYOUTFigure 14 - CONTROL BOARD BUTTONSENTERSTOPCLOSEOPENPOWERINPUTSMOTORCONNECTION PLUG

108 - ACCESSORY INPUTS AND OUTPUTS 8.1 - OutputsFigure 16 - BOARD OUTPUTSCommercial Gate Operator Accessory Outputs:OUT1 and OUT2:(MCHUHCT@KHRNK@SD

11O-View Software Suite. This unit, when matched with the OVIEW Bluetooth or GSM modules, enables remote control and management of the gate control-le

129 - WIRING AND CONNECTIONS Permanent wiring is to be employed for the installation as required by local codes.Use only U.L. listed (or equivalent) n

1310.5 - Exit and edge inputs wiring diagram28 EDGE29 GND30 EXIT31 GND3GD$#&$HMOTSL@XADBNMjFTQDC@R@LNMHSNQDC - +.&HMOTSNQ#(&(

1411 - INSPECTION AND OPERATION Proper inspection of all equipment is required to ensure continuous function-ality, safety and to ensure reliable oper

15q /K@BDBNMSQNKR@LHMHLTLNEEDDS@V@XEQNLSGDF@SDRNSG@SSGDTRDQB@Msee the gate and operate controls but cannot touch the gate or gate op

16%HFTQD&$-$1 ++ 8.433'$/1.&1 ,,(-&!433.-2(-#(" 3$#(-3'$ !.5$1$%$1$-"$2'.4+#!$42$#.-+8 %3$14-

1715 - PROGRAMMING BUTTONS 15.1 - ForceStatic: Set sensitivity to constant force on a scale of 1 to 10 (1 being the most sensitive).Dynamic: Set sens

18q W.TS.EEq !KNBJq 4MAKNBJq .ODM@MC!KNBJq "KNRD@MC!KNBJq .ODM@MC4MAKNBJq "KNRD@MC4MAKNBJTo program weekly events EV

1918 - EMERGENCY VEHICLE ACCESS 18.1 The automatic vehicular gate system must be designed to allow access to emergency vehicles under different opera

2020 - MAINTENANCE SCHEDULE - APOLLO GATE OPENERActive the primary (inherent)reverse system by blocking the gate with a solid object. The gate should

2122 - TEMPLATE FOR INSTALLATION (2)%HFTQD+ 8.433$,/+ 3$Installation layoutEABC10”10”DHINGE CENTERLONG ARMSHORT ARMOUTINCONCRETE PADOUTINDISTAN

2223 - TEMPLATE FOR INSTALLATION (3)Chart DA B C D E Distance32-3/8” 23-1/8” 25-1/8” 25 11 21”Table 421”Figure 31

2324 - COMPACT INSTALLATION ARM MEASUREMENTSFigure 32 - ARM MEASUREMENTS21”25”11”32 1/4”25 1/2”23 3/16”5 7/8” 15 3/4”Ø1/2”1 3/16”7 7/8”7 1/8”Ø1/2”Ø1/2

2425 - GATE ARM INSTALLATIONFigure 33CORRECT LAYOUT INCORRECT INSTALLATIONFigure 34

25This procedure allows slight mechanical adjustment of the gate’s closing angle by extending or retracting the main arm.1. Using a 2.5mm or 3/32 hex

2628 - PROGRAMMING QUICK START 28.1 - Learning the gate1. Install electrical power to the gate opener unit. 2. Install all gate accessories such as

27 Left box is for installer check off and the right box is for cus-tomer check off. TT1. The gate has been checked to make sure it is level and m

1CAUTIONS AND NOTES 2EXTREMELY IMPORTANT 2ETL DEFINITIONS COMPLIANT TO UL325 2 1 - OVERVIEW 21.1 - Gate controller 21.2 - Main control board 21.

Contact usNice Group USA Inc. 12625 Wetmore Road Suite 218 San Antonio, TX 78247 Ph. +1.210.545.2900 Fax [email protected] www.apo

2CAUTIONS AND NOTESThis instruction manual is intended to aid the installer in the overall process of correct installation at the desired location. Pe

32 - GATE INFORMATION2.1 - ASTM F2200Gates shall be constructed in accordance with the provisions given for the appropriate gate type listed, refer to

43 - SAFETY AND CAUTIONS WARNINGIMPORTANT SAFETY INSTRUCTIONSWARNING - TO REDUCE THE RISK OF INJURY OR DEATH:q 1$ # -#%.++.6 ++(-2314"3(.-2

54.3.4 Only install this gate system opener in appropriate manners in which the operation is safe and secure.4.3.5 A gate operator exerts a great am

6%HFTQD.5$1 +++ 8.435.1 - Swing operator cutaway drawings-cont.POWERStandard 120VAC outlet for accessoriesManual ReleaseManual ReleaseHandleBuil

76.4 - Step four-manual releaseHaving removed the top cover, locate the manual release handle. Insert and turn the manual release handle clockwise unt