INSTALLATION INSTRUCTIONS AND SAFETY INFORMATIONFOR THE VIKING SINGLE CONTROL UNITCLASS II, CLASS III, AND CLASS IV Commercial/Residential Vehicular
VIKING TECHNICAL SUPPORT 1.800.908.08848IMPORTANT SAFETY INFORMATIONMAINTENANCERemove the Power Harness from the Control Board (refer to page 14)•Cle
VIKING TECHNICAL SUPPORT 1.800.908.08849a. Use only the following type and size battery(ies): Yuasa NP7-12b. Donotdisposeofthebattery(ies)inre
VIKING TECHNICAL SUPPORT 1.800.908.088410IMPORTANT SAFETY INFORMATIONNOTE: This type on installation DOES NOT reverse the gate all the way back to its
VIKING TECHNICAL SUPPORT 1.800.908.088411NOTE: This type on installation DOES NOT reverse the gate all the way back to its limits when the edge sensor
VIKING TECHNICAL SUPPORT 1.800.908.088412IMPORTANT SAFETY INFORMATION! WARNING! Not Following these instructions may cause severe injury or death.Audi
VIKING TECHNICAL SUPPORT 1.800.908.088413! WARNING: DO NOT allow pedestrian use of this gate.IMPORTANT INSTALLATION INFORMATIONLocate Control Buttons:
VIKING TECHNICAL SUPPORT 1.800.908.088414High Voltage Supply Option! Caution: Always turn off power breakers when working with high voltage. DO NOT co
VIKING TECHNICAL SUPPORT 1.800.908.088415Low Voltage Supply OptionTIP: As an alternative to high voltage, the operator can be power by 24VAC. It is re
VIKING TECHNICAL SUPPORT 1.800.908.088416Motor HarnessNOTE: Refer to the gate operator’s Installation Manual (G-5, X-9 or i-8) for specific instructio
VIKING TECHNICAL SUPPORT 1.800.908.088417OpenLimitCloseLimit! TECHNICAL TIP: The Limit LEDs will illuminate solid when the gate reaches the corrispond
This Single Electronic Control Unit “ECUS” is equipped for use with 115/230VAC, 24VAC/VDC or solar and includes a battery backup system and Vi
VIKING TECHNICAL SUPPORT 1.800.908.088418Initial SettingsCONTROL BOARD SETUP“Timer”Hold Open TimerAutomatically closes the gate after the selected amo
VIKING TECHNICAL SUPPORT 1.800.908.088419Initial SettingsNOTE: Installing a shunt, or jumper, on the pins will activate the feature.CONTROL BOARD SETU
VIKING TECHNICAL SUPPORT 1.800.908.088420Obstruction Sensor (Primary Entrapment Protection)! IMPORTANT: The appropriate “ODS” setting is dependant upo
VIKING TECHNICAL SUPPORT 1.800.908.088421CONTROL BOARD SETUPViking HeaterThe operator has an integrated heater. Activate this feature when the operato
VIKING TECHNICAL SUPPORT 1.800.908.088422Re-Open Photo Beam (vehicular Safety)NOTE: This type of photo-beam installation will stop then RE-OPENS the g
VIKING TECHNICAL SUPPORT 1.800.908.088423Radio Receiver (Typical)! IMPORTANT: The Hold Open “Timer” setting (page 18) effects how the gate will respon
VIKING TECHNICAL SUPPORT 1.800.908.088424Anti-Tail Gate, Open Commands & Guard Station! TECHNICAL TIP: For more information regarding accessory co
VIKING TECHNICAL SUPPORT 1.800.908.088425Viking Loop RackTIP: This operator may be equipped with a pre-wired Loop Rack that plug-in type loop detector
VIKING TECHNICAL SUPPORT 1.800.908.0884265'5' 5'AA5'Gate in Open PositionInsideReopenLoopCenterLoopOutsideReopenLoopExitLoopMake E
VIKING TECHNICAL SUPPORT 1.800.908.088427Magnetic Lock, Lock SolenoidNOTE: Viking Access Systems does not provide external gate lock devices. These it
ECU Single Vehicular Swing Gate Controller • Revision ECUSNXMN10.G • September 2013
VIKING TECHNICAL SUPPORT 1.800.908.088428Barrier Arm (B-12) Synchronization OptionNOTE: The Control Board provides a convenient solution for applicati
VIKING TECHNICAL SUPPORT 1.800.908.088429(THIS PAGE LEFT BLANK INTENTIONALLY)
VIKING TECHNICAL SUPPORT 1.800.908.088430LED ReferencesIn addition to the LCD Display, the control board LEDs monitor the various circuits of the cont
VIKING TECHNICAL SUPPORT 1.800.908.088431LED ReferencesUse the table below to identify the corresponding “TS Ref#” and refer to page 32-35 for further
VIKING TECHNICAL SUPPORT 1.800.908.088432TROUBLESHOOTINGCall out LCD Display, Diag-nose Button and Diag-nose LEDLCD MSG MeaningPage 35 TS Ref #s VIKIN
VIKING TECHNICAL SUPPORT 1.800.908.088433TROUBLESHOOTINGLCD MSG MeaningPage 35 TS Ref #sMulti Meter DisplaysMOT AMP __._ AThis is the motor current
VIKING TECHNICAL SUPPORT 1.800.908.088434TROUBLESHOOTINGLCD Display References LCD MSG MeaningPage 35 TS Ref #sError MessagesERR AC LOWIndicates th
VIKING TECHNICAL SUPPORT 1.800.908.088435TROUBLESHOOTINGSolutionsBegin the troubleshooting process by referring to the error messages on the LCD Displ
VIKING TECHNICAL SUPPORT 1.800.908.088436Access Control ConnectionsAppendix (A)Power ConnectionsThe control board provides a 24v DC output to power ex
VIKING TECHNICAL SUPPORT 1.800.908.088437Relays In GeneralNOTE: Viking Access Systems does not provided the external safety devices and access control
VIKING TECHNICAL SUPPORT 1.800.908.08842PARTS DIAGRAM:Item Description Part No.1 Motor Harness (Single only) ECUMTHRN 2 Power Harness DUPHCECU3
VIKING TECHNICAL SUPPORT 1.800.908.088438Common Radio Receivers - ConnectionsAppendix (B)
VIKING TECHNICAL SUPPORT 1.800.908.088439Solar ApplicationsNOTE: Viking recommends Solar Package (part # VA-SOCHP) for most general solar applications
VIKING TECHNICAL SUPPORT 1.800.908.088440VIKING EXPANSION PRODUCTSVIKING KONNECT Master/Slave Kit Secure and reliable Master/Slave communication using
Viking Access Systems is continuously working hard to identify and design products that will appeal to the industry and it’s needs. As t
VIKING ACCESS SYSTEMS 631 Wald Irvine, CA 92618Phone 800.908.0884Fax 949.753.1640www.vikingaccess.comSTANDARD FEATURESINSTALLATION DATE: ____________
VIKING TECHNICAL SUPPORT 1.800.908.08843ECU BOX DIMENSIONS:
VIKING TECHNICAL SUPPORT 1.800.908.08844CONTROL BOARD REFERENCES:1. POWER HARNESS CONNECTOR provides power to the control board. pg 14-152. “OPEN LE
VIKING TECHNICAL SUPPORT 1.800.908.08845PARTS DIAGRAM/PARTS LIST 2ECU BOX DIMENSIONS 3CONTROL BOARD REFERENCES
VIKING TECHNICAL SUPPORT 1.800.908.08846IMPORTANT SAFETY INFORMATIONIMPORTANT SAFETY INSTRUCTIONS! WARNING! To reduce the risk of severe injury or dea
VIKING TECHNICAL SUPPORT 1.800.908.08847IMPORTANT SAFETY INFORMATIONIMPORTANT INSTALLATION INSTRUCTIONS (Continued)6. Controls intended for user activ
Comments to this Manuals