Underground Swing Gate OperatorUL325 - UL991FAAC International Inc.Headquarter & East Coast Operations5151 Sunbeam RoadSuites 9-11Jacksonville, FL
10FAAC Model 770 24V Underground Swing Gate OperatorAt regular intervals, check the structure of the gate and make sure that the hinges are in perfect
11FAAC Model 770 24V Underground Swing Gate Operator770 24 VTablePARTS LIST1/1/1900Start Date1/1/9999End Date770 24 VDCCodeATTUATORE ELETTROMEC. INTER
SETTING+J24DL19 DL20 DL21 DL22DL14 DL15 DL16 DL17 DL18Main power supply115/230 V~ 50/60 Hz switchableSecondary power supply24 Vdc -
A B STP CL OP OPEN FSWFig. A2PIN LABEL FUNCTION2 EASY 2 EASY Input for bus 2easy accessories (encoder)1 OPEN A N.O. Contact for tot
FSWSTP CL OPHow to connect Normally Open contacts. (Connect them in parallel)How to connect Normally Close contacts. (Connect them in ser
FSWSTP CL OP FSWSTP CL OPConnection of two pairs of closing photocellsConnection of a pair of closing photocells, a pair
88 FSWSTP CL OP FSWSTP CL OP FSW STP CL OP FSW STP CL OP To use the FAIL-SAFE mode connect the negative
4. PROGRAMMING OPERATING LOGIC DS 1: SW 1 - SW 2 - SW 3 LOGICSW 1SW 2SW 3PAUSE TIMEDESCRIPTIONE (default)SemiautomaticOFF OFF OFF NOOne comman
6TR 3 – SPEED ADJUSTMENT FOR MOTOR1 AND MOTOR 2 Turn clockwise to increase the opening and closing speed TR 4 – SENSITIVITY ADJUSTEMENT FOR OBSTACLE
BOARD SETUP DS 1: SW 4 to SW 12OPENING DELAYSW 4The opening of leaf 2 is delayed after the opening of leaf 1. This is to avoid that the gate’s lea
2FAAC Model 770 24V Underground Swing Gate OperatorCONTENTSFAAC Model 770 24V - Rev: 02 - JUN 2012 Read this instruction manual before you begin inst
DS2SETTING+J2412345678 910 DL19 DL20 DL21 DL22 DL14 DL15 DL16 DL17 DL18DS 2 OPERATOR SELECTIONOPERATOR TYPE SW 1 SW 2 SW 3S45
A11LEDDESCRIPTIONLED STATUS In BOLD the normal state with gate closed and workingON STEADY OFF BLINKING1LED BATTERYBoard working on AC powerBoard work
WARNING: If the time learning setup is done automatically then the slow down points are set by the board on his ownMove the leafs to the mid positionV
The obstacle detection function is achieved by controlling the current absorption and / or through the encoder connected to the motors.If the gate enc
AC POWER CONNECTIONTo connect AC power to the controller:1. Turn the circuit breaker for the AC gate operator power OFF before connecting the AC input
LOGIC “E” PULSESSYSTEM STATUSOPEN A OPEN B CLOSE STOP FSW OP FSW CL FSW CL/OPCLOSED opens the leaves opens leaf 1 no effectno effect (OPEN disabled)
LOGIC “EP” PULSESSYSTEM STATUSOPEN A OPEN B CLOSE STOP FSW OP FSW CL FSW CL/OPCLOSED opens the leaves opens leaf 1 no effectno effect (OPEN disabled)
LOGIC “B” PULSESSYSTEM STATUSOPEN A OPEN B CLOSE STOP FSW OP FSW CL FSW CL/OPCLOSED opens the leaves no effect no effectno effect (OPEN disabled)no e
A18E024U CONTROL BOARDTo the original purchaser only: FAAC International, Inc., warrants, for twenty-four (24) months from the date of invoice, the ga
3FAAC Model 770 24V Underground Swing Gate Operator1. Install the gate operator only when the following conditions have been met:• The operator is a
4FAAC Model 770 24V Underground Swing Gate OperatorGate ConstructionVehicular gates should be constructed and installed in accordance with ASTM F2200:
5FAAC Model 770 24V Underground Swing Gate OperatorRESIDENTIAL VEHICULAR GATE OPERATOR CLASS IA vehicular gate operator system intended for use in a s
6FAAC Model 770 24V Underground Swing Gate Operator1 Foundation Box2 Bores for Fastening Box Cover 3 770 Operator4 Gate Support Bracket 5 Locking
7FAAC Model 770 24V Underground Swing Gate Operatorb) For Existing Gates with Adjustable Hinges:• Remove the bottom hinge.• Slacken the top hinge.
8FAAC Model 770 24V Underground Swing Gate Operatormin ⅜13min 1½CC+1Fig. 9• Determine the correct location of the leaf on the “U” prole with referen
9FAAC Model 770 24V Underground Swing Gate Operator1. Program the electronic control unit according to your requirements, following the relevant inst
Comments to this Manuals